SERVICE PROCEDURES
2016+ 32mm/34mm FLOAT NA2 Rebuild
Required Parts
- 803-00-962 Seal Kit: 32 FLOAT NA2 Rebuild
- 803-00-963 Seal Kit: 34 FLOAT NA2 Rebuild
Required Tools
- 398-00-657 Tooling: Bullet, Sealhead To Shaft, FLOAT NA 2
- 398-00-681 2002-017 32 Damper-side and ALL 32-34-36-40 Spring-side Removal Tool
- 398-00-682 2005-017 34-36-40 Damper-side Removal Tool (needed only for 34mm forks)
- 398-00-702 Tooling: Fork Topcap Socket, 26mm, 3/8 Drive
- 803-01-324 Kit: Tooling: 2019 Clamps, Grip Damper, Body and Shaft
The following procedure guides you through the rebuild of the FLOAT NA2 air spring found in 2016+ 32mm and 34mm forks.
WARNING: Always wear safety glasses and protective gloves during service to prevent potential injury. Failure to wear protective equipment during service may lead to SERIOUS INJURY OR DEATH.
WARNING: FOX products should be serviced by a trained bicycle service technician, in accordance with FOX specifications. If you have any doubt whether or not you can properly service your FOX product, then DO NOT attempt it. Improperly serviced products can fail, causing the rider to lose control resulting in SERIOUS INJURY OR DEATH.
WARNING: Never attempt to modify air volume spacers or air shaft assemblies, as this can damage your fork causing a loss of control of the bicycle leading to SERIOUS INJURY or DEATH.
WARNING: FOX suspension products contain pressurized nitrogen, air, oil, or all 3. Suspension misuse can cause property damage, SERIOUS INJURY OR DEATH. DO NOT puncture, incinerate or crush any portion of a FOX suspension product. DO NOT attempt to disassemble any portion of a FOX suspension product, unless expressly instructed to do so by the applicable FOX technical documentation, and then ONLY while strictly adhering to all FOX instructions and warnings in that instance.
WARNING: Modification, improper service, or use of aftermarket replacement parts with FOX forks and shocks may cause the product to malfunction, resulting in SERIOUS INJURY OR DEATH. DO NOT modify any part of a fork or shock, including the fork brace (lower leg cross brace), crown, steerer, upper and lower leg tubes, or internal parts, except as instructed herein. Any unauthorized modification may void the warranty, and may cause failure or the fork or shock, resulting in SERIOUS INJURY OR DEATH.
Step 1
Remove the blue air cap and cover the air valve with a rag as you release the air pressure.
WARNING: Please verify that all air has been released from the air chamber by pushing down on the Schrader valve core. Failure to release all air pressure before further disassembly may cause parts to eject causing SEVERE INJURY OR DEATH.
Step 2
With a chamfer-less 6-point 26mm socket (PN: 398-00-602), unthread the topcap assembly completely (counter-clockwise). Pull straight up to remove the entire topcap assembly from the left side upper tube. Some upward force might be needed to overcome the friction of the stock air volume spacer.
Step 3
Use a 2mm hex wrench to unthread the set screw in the red rebound knob. Remove the knob and set it aside.
Step 4
Use a 10mm socket to unthread and remove the air side bottom nut. Remove and discard the original crushwasher.
Note: You may need a custom 10mm socket that has been reduced in outer diameter to clear certain Step-Cast lower leg castings.
Step 5
32mm: Use a 10mm socket to remove the damper side bottom nut. Remove and discard the original crushwasher.
Note: You may need a custom 10mm socket that has been reduced in outer diameter to clear certain Step-Cast lower leg castings.
34mm: Use a 15mm socket to remove the damper side bottom nut. Make sure to remove and discard the original crushwasher which may be stuck to the bottom nut.
Step 6
Use Damper Removal Tools 398-00-681 and 398-00-682 to dislodge the shafts from the lowers. Make sure that you have approximately half of the available threads engaged with your tool before striking with your mallet. Remove the damper removal tools, then bring the fork upright over an oil basin to drain. After oil stops draining from the lowers, pull the lowers off of the upper tubes and set them aside.
Step 7
Remove the retaining ring from the bottom of the air side upper tube. 32mm forks use a double wound flat retaining ring. 34mm forks use a single wound Hoopster style retaining ring.
Step 8
Thread the damper removal tool (PN: 398-00-681) onto the air shaft and pull out from the upper tube to remove the air shaft assembly.
Step 9
Wipe grease off of the air shaft assembly to make it easier to handle, then slide the neg plate toward the base stud, leaving enough space to access the base stud wrench flats.
Step 10
Use a lint-free paper towel to remove the q-ring from the air piston. DO NOT use any tools to remove the q-ring as you can damage the sealing surfaces of the piston. Install a new greased q-ring from the kit making sure it is fully seated and not twisted.
Step 11
Clean the shaft with Isopropyl alcohol then clamp it in your 10mm shaft clamps (PN: 803-01-324). Remove and discard the o-ring from the base stud then carefully apply heat to the shaft at the base stud with a propane torch for 5-10 seconds to break down the Loctite.
Step 12
Unthread the base stud counter-clockwise with a 12mm wrench, then lift up to remove. For forks 130mm and longer, remove the remaining o-ring on the base stud and replace with a new greased one from the kit. Forks 120mm and shorter do not have this seconday o-ring on the base stud.
Step 13
Lift up on the neg plate to remove it from the shaft. Remove the external o-ring and replace it with a new greased one from the kit. Remove the two seals from the inside of the neg plate.
Step 14
Install a new greased Q-ring from the kit into the uppermost seal groove. Insert the seal through the bushing and guide it into position with a blunt tool like a 2mm hex wrench or similar. Make sure the Q-ring is fully seated in it's groove and not twisted.
Step 15
Install a new greased u-cup seal from the kit into the lower seal groove, making sure to orient the u-cup lip down as shown.
Step 16
Insert the FLOAT NA2 bullet tool (PN: 398-00-657) into the shaft, then coat it with a thin film of Slick Honey. Reinstall the neg plate with it's flat side down. Remove the bullet tool.
Step 17
Apply 1-2 drops of red Loctite 262 to the threads inside the shaft, taking caution not to get Loctite in the area of the shaft where the base stud o-ring will seat. Insert the base stud and thread it in clockwise, tightening to 50 in-lb (5.7 Nm) torque with a 12mm crow's foot.
Step 18
Install a new greased o-ring from the kit onto the base stud.
Step 19
Apply a thin film of Slick Honey to the inside of the upper tube. Apply a thick film of Slick Honey to the air shaft assembly in the areas of the piston, neg plate, and shaft above the neg plate.
Step 20
Insert the air shaft assembly into the end of the upper tube. Push the air shaft assembly into the upper tube far enough to allow you to start the neg plate into the upper tube. Push the shaft into the upper tube to pull the neg plate into its installed position.
Step 21
Replace the retaining ring making sure it is fully seated in its groove by pulling on the air shaft. (32mm version shown)
Step 22
Inject 3cc of FOX 20wt. Gold oil into the main air chamber through the top of the upper tube. Reinstall the topcap into the fork crown and tighten clockwise to 220 in-lb (24.8 Nm) torque with your 6-point chamfer-less 26mm socket.
Step 23
Add air pressure to your desired setting using a FOX high pressure pump. See the Setting Fork Air Pressure section for more information. Reinstall the blue air cap.
Step 24
Install the Lower Leg Assembly onto the upper tubes. Inject the approprate amount of bath oil into each leg through the bottom hole. Please reference the bath oil chart for your fork:
2025 Bath Oil Volume Chart
2024 Bath Oil Volume Chart
2023 Bath Oil Volume Chart
2022 Bath Oil Volume Chart
2021 Bath Oil Volume Chart
2020 Bath Oil Volume Chart
2019 Bath Oil Volume Chart
2018 Bath Oil Volume Chart
2017 Bath Oil Volume Chart
2016 Bath Oil Volume Chart
2015 Bath Oil Volume Chart
2014 Bath Oil Volume Chart
Step 25
Install a new crushwasher on each side followed by the appropriate bottom nut. Torque both bottom nuts to 50in-lb (5.7 Nm).
Step 26
Use a 2mm hex wrench to install the red rebound knob. Make sure that the set screw lines up with the depression in the rebound adjuster shaft. Clean the exterior of your fork.
Step 27
After assembly you must compress the fork 3-5mm very slowly until you feel the chamber pressures equalize.