SERVICE PROCEDURES

Step 1

Remove the Saddle Clamps and hardware. Turn the 4mm hex bolts counter-clockwise to remove them from the Barrel Nuts. Set all clamps and hardware aside.

Step 2

Clean your bike work stand clamps and the exterior of the seatpost to prevent damage during clamping. Clamp the seatpost in your workstand, then unthread the Bottom Cap counter clockwise while holding it by it's thickest section to remove it from the lower post.

Step 3

Unthread the Lower Post Collar by turning it counter-clockwise when viewed from the top of the seatpost. You may use Knipex smooth-jawed parallel pliers but the FOX tool (PN: 398-00-896) will assist in applying proper torque at a later step (tool not shown as procedure was shot before tooling arrived. Images will be updated).

Step 4

Remove the wire retaining ring from within the lower post and set it aside.

Step 5

Separate the Upper Post Assembly from the Lower Post taking care not to lose the Index Pins and ball bearing as parts may fall out during separation.

Step 6

Take note of the position of the ball bearing and mark the anti-rotation hole that the ball bearing was found in.

If you use a Sharpie or other marker to make this mark, take care not to remove the mark as you clean parts throughout the rebuild. A scribed line is also an option for marking the position of the ball bearing.

Remove the 2mm ball bearing and set it aside in a protected location as it is small and easy to lose.

Step 7

Clean the Lower Post with Ispropyl alcohol and a lint-free paper towel taking care not to leave any paper towel residue inside the Lower Post.

Step 8

Carefully clamp the Shaft in your shaft clamps (PN: 803-00-147) using proper shaft clamp techniques to prevent damage to the sealing surface, then unthread the Shaft Lug counter clockwise with a 10mm wrench to remove it. Remove the original bottom out bumper.

Step 9

Remove the Lower Bushing, o-ring under the Lower Bushing, Index Pins, Upper Bushing, and Lower Post Collar. (Note: an early down-rev Upper Bushing is shown. MY21 production Transfer seatposts will have a smooth-rimmed Upper Bushing without the castellation).

Step 10

If the original Collar and wiper are present, please update to the new Collar and Wiper Assembly (PN: 825-00-150-KIT [FOX] or 825-00-151-KIT [Race Face]).

Note that the o-ring was moved from it's original position during disassembly. The correct o-ring position is noted in the drawing.

Step 11

To replace the wiper in the updated collar assembly (825-00-150-KIT for FOX or 825-00-151-KIT for Race Face) temporarily thread the collar assembly onto the lower post for added support. Use a flat tool with a rounded tip to pry up on the wiper without scratching the inside of the collar. 

Step 12

Clamp the wiper installation tool (803-01-917) into your vise as shown. Coat the outer edge of the new wiper with a thin film of Slick Honey then place the prepared wiper into the tool with the wipers lip facing down into the tool.

Step 13

Press the collar straight down onto the prepared wiper until the collar is flush with the top of the installation tool. Remove the collar assembly from the lower post and set them aside.

Step 14

Clamp the Upper Post in your bike work stand, then slowly unthread the bleed screw to release IFP pressure. Remove the screw from the Sealhead with a 1.5mm hex wrench. The bleed screw is the M3 screw that is farthest from the two blind holes in the Sealhead. Make sure that all pressure is released before moving on to the next step. Remove the 0.083" ball bearing from beneath the bleed screw. A magnet may be necessary for removal.

Step 15

Remove the fill screw from the Sealhead with a 1.5mm hex wrench. The fill screw is the M3 screw closest to the blind holes in the Sealhead. Remove the 0.083" ball bearing from beneath the bleed screw. 

Step 16

With the Upper Post clamped vertically in your bike work stand unthread (counter-clockwise) and remove the Anti-Tamper screw with a 5/64 Anti-Tamper Hex wrench. You may need to hold the Top Cap Assy from turning with a pin spanner.

Step 17

Slowly press the Top Cap Assy down into the Upper Post to make room to access the wire retaining ring. Oil may spray out at this point. It is recommended to cover the post with a lint-free paper towel before doing this step. No paper towel is shown in order to illustrate the step more clearly. Use a shim to remove the wire retaining ring. Set the ring aside.

Step 18

Thread the Trek Thru Shaft IFP Removal Tool (PN: 398-00-749) clockwise into the Top Cap Assy and pull up to remove. Replace the o-ring on the Top Cap Assy with a new greased one from the kit then set aside.

Step 19

Pour the oil out through the top of the post into your waste oil basin. Push the Piston Assembly out through the top of the Upper Post with a wooden or plastic dowel.

Step 20

Clamp the Upper Post in your bike work stand with the bottom end facing up. Push the Sealhead in to make room to access the wire retaining ring. Remove the wire retaining ring. Set the ring aside.

Step 21

Thread an M3 screw into both the fill and bleed ports of the Sealhead. Screw 019-01-083 may be used for this. Lift up on both screws to remove the Sealhead from the Upper Post. Replace the Sealhead o-rings with new greased ones from the kit. Please update to the new sealhead (PN: 825-03-016-KIT) if an original sealhead is found.

Step 22

Remove the wire retaining ring from beneath the Sealhead. Insert the Delrin Push Rod (PN: 398-00-740) into the top of the Upper Post, then push the IFP out through the bottom. Replace both IFP seals with new greased ones from the kit.

Step 23

Clean the Upepr Post with Ispropyl alcohol and a lint-free paper towel taking care not to leave any paper towel residue inside the Upper Post.

Step 24

Remove the Push Rod from the Shaft. Clamp the shaft in your shaft clamps, then unthread the Main Piston Assembly counter-clockwise with a 9mm wrench.

Step 25

Clean the Shaft with Isopropyl alcohol and a lint-free paper towel. Clamp the cleaned shaft in your clamps with the smaller diameter unthreaded portion of the shaft facing up.

Step 26

Coat the seals of the new Main Piston Assembly (in rebuild kit) with a thin film of Slick Honey. Thread the new Main Piston Assembly onto the shaft clockwise then tighten to 40 in-lb (4.5 Nm) torque. (Note: while a wrench is shown, please use a crow's foot to tighten the Piston Assembly to proper torque).

Step 27

Coat the Push Rod with a thin film of Slick Honey then reinstall it into the shaft as shown. Cycle the Push Rod against your work surface to check that it moves and returns smoothly after actuation.

Step 28

Coat the IFP with a thin film of Slick Honey then reinstall into the bottom of the Upper Post as shown. Reinstall the first wire retaining ring as shown.

Step 29

Install the Transfer Bullet Tool (PN: 398-00-738) onto the Shaft of the Piston Assembly then coat with a film of Slick Honey. Reinstall the Piston Assembly into the Upper Post through the top of the post as shown.

Step 30

Invert the Upper Post so the it is upright. Lift the Main Piston Assembly out of the top of the Upper Post just enough to allow you to fill the Upper Post with FOX 1.5wt. Clear oil. Slowly push the Main Piston Assembly into the top of the Upper Post.

Step 31

Install the Spool Valve Compressor tool (PN: 398-00-700) into the Shaft Lug by threading it in clockwise. Temporarily reinstall the Shaft Lug onto the end of the shaft by threading it on clockwise. You may also use the Open Valve tool (398-00-735) in place of the Shaft Lug and Spool Valve Compressor as an option.

Step 32

Pour FOX 1.5wt oil into the Upper Post above the Piston Assembly until full. Keep the post vertical and slowly cycle the Shaft fully up and down 5-7 times while watching for bubbles at the top of the Upper Post. 

Step 33

When no new bubbles appear while cycling the Shaft, fully extend the Shaft and remove the Open Valve tool or Shaft Lug with the Internal Spool Valve Compressor tool. Install the appropriate IFP Height tool for your post, then reinstall the Shaft Lug with the Internal Spool Valve Compressor tool.

Step 34

Hold the Shaft at full extention while you insert the IFP tool up into the bottom of the Upper Post until it bottoms out. Remove the Shaft Lug with the Internal Spool Valve Compressor tool and the IFP tool.

Step 35

Reinstall the Top Cap Assy into the top of the Upper Post, then press it down to seat. Oil will spray out at this point. It is recommended to cover the post with a lint-free paper towel before doing this step. Install the wire retaining ring above the Top Cap Assy, then thread in the Trek Thru Shaft IFP Removal Tool and pull up to seat the Cap. Remove the tool.

Step 36

Make sure that the Top Cap is topped off with oil. Hold the Top Cap Assy with your pin spanner white tightening the Anti-Tamper screw with a 5/64" hex wrench clockwise to 11 in-lb (1.2 Nm). 

Step 37

Add 0.5-1cc of Float Fluid to the IFP chamber. Install the 8mm Shaft Bullet tool onto the shaft and coat it with a thin film of Slick Honey.

Step 38

Remove the setscrew from the fill hole by unthreading counter-clockwise with a 1.5mm hex wrench. Remove the ball bearing with a magnet. Coat the updated Sealhead with a thin film of Slick Honey then reinstall the Sealhead onto the Shaft with its flat side facing up as shown. Updated sealheads can be identified by the extra drill point mark shown below. Remove the Bullet tool, then push the Sealhead into the Upper Post as far as it will go.

Step 39

Reinstall the wire retaining ring into the bottom of the Upper Post making sure to orient the split in the ring so it is positioned 180 degrees from the Fill Port.

Step 40

Install the 2mm ball bearing into the bleed hole, apply blue Loctite 242 onto the M3 set screw, then install the set screw. Install an M3 screw in the fill port and hold it to prevent Sealhead rotation while you tighten to 3 in-lb (0.3 Nm) torque with a 1.5mm hex wrench. The bleed screw is the M3 screw that is farthest from the blind holes in the Sealhead.

Step 41

Install the Nitrogen Fill Open Valve tool (PN: 398-00-735) onto the end of the Shaft.

Step 42

There are two styles of fill tool that can be used with the Transfer seatpost.

Instructions for using the original style of fill tool (803-01-595) start at step 43.

Skip to step 44 for instructions on using the new compact fill tool (PN: 803-01-931).

Step 43

Install the Gas Fill Assembly (PN: 803-01-595) into the fill port. Be careful not to scratch the shaft as you install and use the Gas Fill Assembly. Hold the Shaft to help you tighten the Gas Fill Assembly into the fill port fully. Use the Gas Fill Support Tool (PN: 398-00-758) or wrap a small piece of tape around the Shaft and Gas Fill Assembly to add support and prevent damage to the Gas Fill Assembly.

Step 44

Slide the compact fill tool (PN: 803-01-931) over the shaft making sure to align the pin with the blind hole in the sealhead. Note, the gap in the tool should be centered over the bleed hole in the sealhead. Use a 2.5mm hex wrench to tighten the fill tool bolt clockwise until snug. Do not exceed 1 in-lb torque.

While the original style of fill tool is shown, follow the next steps with either fill tool to complete the gas fill of the Transfer seatpost. 

Step 45

Install the Gas Fill Assembly onto your Nitrogen system, then support the seatpost so it does not rely on the Gas Fill Assembly. The Gas Fill Assembly can be damaged if used to support the weight of the seatpost.

Step 46

Set your regulator to 0psi (0 bar) and slowly increase pressure over the course of 30 seconds until you reach 325 psi.

Step 47

Remove the tape (if present) and Gas Fill Assembly from the Sealhead. Remove the Nitrogen Fill Open Valve tool. Install the 2mm ball bearing into the fill hole, apply blue Loctite 242 onto the M3 set screw, then install the set screw. Tighten to 3 in-lb (0.3 Nm) torque with a 1.5mm hex wrench. Check that both the fill and bleed screws are properly tightened to 8 in-lb (0.9 Nm) torque.

Step 48

Apply a thin film of Slick Honey to the inside of the new Wiper from the kit. Install the Lower Post Collar onto the Upper Post as shown taking care not to damage the wiper seal lip on the edge of the post near the Lower Bushing position.

Step 49

Install the new Upper Bushing from the kit with its "crown-shaped" portion oriented toward the top of the post. Install the new o-ring from the kit onto the upper post followed by the new Lower Bushing. Do not use sharp tools for installation, the pick is shown to indicate the o-ring position.

Step 50

Install the new bottom out bumper from the kit onto the Shaft lug then thread the Shaft Lug onto the Shaft clockwise. Clamp the Shaft, then tighten the Shaft Lug onto the Shaft to 30 in-lb (3.4 Nm) torque with your 10mm wrench.

Step 51

Fill the Index Pin slots with Slick Honey, then install the Index Pins.

In some cases, the rear-most oriented index pin can bind between the upper and lower posts when excessive seatpost clamping force is used. This can cause unwanted friction and in some cases can prevent the post from fully extending. FOX and Race Face now approve the usage of only two index pins in place of three. The rear-most of the three index pins should be omitted, and the remaining two should be exchanged for slightly larger pins to prevent inappropriate rotational play.

Use the conversion chart below to select replacement pins when switching from 3 pins to 2 pins. In cases of older posts that exhibit wear from significant riding, you may need to select a slightly larger pin than indicated in the chart to acheive appropriate seatpost performance.

Index pins are available individually or in bulk bags of 6 pins each.

Step 52

Install the anti-rotation 2mm ball bearing into the pocket on the Shaft Lug that you marked during disassembly. The marked pocket should align with the saddle clamp and the Index Pin that is farthest from the other two. 

Step 53

Align the anti-rotation ball bearing with the groove in the inside of the Lower Post that is inline with the laser etching on the back of the Lower Post. Slowly feed the Upper Post Assembly into the Lower Post. 

Note: Increased force may be required to install the upper post into the lower post as the lower bushing is energized by the o-ring.

Step 54

Loosely position the Upper Post upside down in the Upper Bushing Installer (PN: 803-01-496) so the Upper Bushing rests on the tool. Push the Lower Post down against the tool to install the Upper Bushing. (Note: Early versions of the Upper Bushing and Upper Bushing Installer are shown. The procedure will be identical for the new smooth-rimmed Upper Bushing without castellation and the new 2021 Transfer Upper Bushing Installer {PN: 803-01-496}).

Step 55

Reinstall the wire retaining ring into the bottom of the Lower Post. Compress the seatpost slightly to seat the Shaft Lug against the retaining ring.

Step 56

Thread the Bottom Cap into the end of the Lower Post. Tighten the Bottom Cap clockwise using its thickest part to 40 in-lb (4.5 Nm) torque.

Step 57

Apply a Blue Loctite 242 to the Lower Post threads then reinstall the Lower Post Collar tightening clockwise (when viewed from the top of the post) to 12 in-lb (1.4 Nm) torque.

Step 58

Reinstall the Barrel Nuts into the post head followed by the Saddle Clamp Bolts. Reinstall the Saddle Clamps making sure all arrows face the front of the post.