OWNER'S MANUALS

SHOCK- 2014 FLOAT CTD DrCV

SHOCK- 2014 FLOAT CTD DrCV

Travel

1.750"

1.875"

2.000"

2.125"

2.250"

2.375"

Features/Adjustments

 

Factory FLOAT CTD DrCV; Kashima Coated air sleeve and body, lever actuated Climb/Trail/Descend (3 position), rebound, air spring pressure. 

Factory FLOAT CTD Remote DrCV; Kashima Coated air sleeve body, remote actuated Climb/Trail/Descend (3 position), rebound, air spring pressure.

Performance FLOAT CTD DrCV; Anodized air sleeve and body, lever actuated Climb/Trail/Descend (3 position), rebound, air spring pressure. 

Evolution FLOAT CTD DrCV; Anodized air sleeve and body, lever actuated Climb/Trail/Descend (3 position), rebound, air spring pressure. 

Spring

DrCV Air

Riding style

XC, Trail, AM, FR

Installing Your Shock

Step 1

Check for clearance before riding.

If you are installing your shock on a bike for which the shock was not original equipment, follow the steps below to ensure proper clearance before riding.

 

  1. Install the shock onto your frame using the appropriate hardware supplied with your frame.
  2. Remove the air cap and let all air out of the main air chamber.
  3. Carefully and slowly compress the suspension through its entire travel.
  4. Check that no part of your shock contacts any portion of your frame or linkage as it cycles through its travel.
  5. Pressurize your main air chamber to between 50-300psi to prepare to set sag as described in the "Setting Shock Air Pressure" section below.

Before You Ride

Step 1

Make sure that your shock is ready to ride

  1. Clean the outside of your shock with mild soap and water and wipe dry with a soft rag.
    • Do not use any solvents or de-greasers as these products can damage the shock's exterior finish.
    • Do not use a high pressure washer or spray water directly at the seal/shock body junction.
  2. Inspect the exterior of your shock. The shock should not be used if any of the exterior parts appear to be damaged
    • Contact your local FOX dealer or FOX directly for further inspection or repair.
  3. Make sure that your quick-release levers (or thru-axles) are properly adjusted and tightened.
  4. Check your headset adjustment. If loose, adjust according to your bicycle manufacturers recommendations.
  5. Check that all brake cables or hoses are properly fastened.
  6. Test the proper operation of your front and rear brakes on lever ground.

Setting DrCV Shock Air Pressure

FLOAT DrCV CTD shocks have a maximum pressure of 300psi

Step 1

Sag should be set to 25 - 30% of total shock travel

    1. Cycle your DrCV shock through at least 60% of its total travel by pushing down on the bikes saddle.
    2. Unscrew the black air cap to expose the schrader valve.
      float-ctd-air-cap.jpg
    3. Slide your shocks sag setting o-ring up against the shock dust wiper.
      float-x-sag-oring.jpg
    4. Rotate the CTD lever to the Descend mode (fully counter-clockwise).
      • If you have a FLOAT  CTD Remote shock, click the black release lever once to set the shock to Descend mode.
    5. Dressed to ride (including a filled hydration pack, if you use one), position your bike next to a wall or table to support yourself. Mount your bicycle. Assume your riding position for at least 10 seconds, allowing the suspension to fully settle. Make sure you distribute your weight evenly between the saddle, handlebars and pedals.
    6. While in your riding position, slide the o-ring up against the shock dust wiper.
    7. Dismount your bike without bouncing, to avoid further moving the o-ring. Measure the distance between the dust wiper and the o-ring. This is your sag measurement. Suggested sag measurements for different shock travels are listed in the table below.
    8. Thread your shock pump onto the air valve until the pump shows a pressure reading on the gauge. Continue to thread the pump on until you notice an increase in pressure on your pumps gauge. 
    9. Add or remove air pressure as needed, then remove your pump from the air valve.
    10. Cycle your DrCV shock through at least 60% of its total travel by pushing down on the bikes saddle.
    11. Repear steps 3-7 and recheck sag measurement.
    12. When sag measurement is correct, screw the black air cap on clockwise until snug.

     

    Suggested Sag Measurements
    2014 Trek Model Shock Travel 25% Sag (Firm) 30% Sag (Plush)
    Lush Carbon 26/29 1.75 in./44mm 0.43 in./11mm 0.52 in./13.2mm
    EX 29/Rumblefish 1.875 in./48mm 0.46 in./12mm 0.56 in./14.4mm
    EX 26 2.00 in./51mm 0.50 in./12.7mm 0.60 in./15.3mm
    Remedy 29 2.125 in./54mm 0.53 in./13.5mm 0.63 in./16.2mm

    Remedy 27.5

    2.25 in./57mm 0.56 in./14.3mm 0.67 in./17.1mm

    Slash 27.5

    2.375 in./60mm 0.59 in./15mm 0.71 in./18mm

It is necessary to cycle the DrCV shock through at least 60% of total shock travel at least once after removing your shock pump, before measuring sag.

Do not attempt to service the DrCV dual-chamber air valve, or remove and reinstall its core! The dual-chamber air valve should only be serviced by FOX US or an Authorized International FOX Service Center »

Adjusting Rebound

Step 1

Rebound controls how fast the shock extends after compressing

float-ctd-reb-knob.jpg

Rebound controls the rate of speed at which the shock extends after compressing. Turning the red rebound knob clockwise (in) slows down rebound, turning the red rebound knob counter-clockwise (out) speeds up rebound. Rebound damping should only be set after first setting your air pressure by measuring sag.

  1. Make sure your CTD adjuster is set in Descend mode (fully counter-clockwise).
  2. Starting with the rebound adjuster in the fully open position (counter-clockwise) push down on the saddle to compress the shock and feel its return speed.
  3. Increase rebound damping by turning the red rebound knob clockwise (when viewed from the end of the shock with the air valve) until when tested, the shock returns quickly but does not top out.

Top out is felt when a shock fully extends too quickly and comes to an abrupt stop when it reaches full extension (you will hear/feel a small noise). Top out should be avoided through proper rebound setting. 

Climb, Trail, Descend

Step 1

Easy on-the-fly adjustments for unprecedented control and performance

The blue CTD lever lets you to switch between the Climb, Trail, and Descend modes. Each mode is optimized for each specific type of terrain, providing exceptional performance and riding enjoyment with your shock. CTD allows for complete rider control as one can experiment using different modes on various different types of terrain.

 

Climb Mode:

ctd-bv-c.jpg

Rotate the blue CTD lever fully clockwise to set the shock in Climb mode. Climb mode is a very firm low-speed compression setting (not designed to be a solid lockout). This setting is most useful for climbing and sprinting.

 

Trail Mode:

ctd-bv-t.jpg

Rotate the blue CTD lever to the middle setting to set the shock in Trail mode. Trail mode offers less compression damping than Climb mode. Use this setting when pedaling on undulating terrain, and for preventing excessive travel in technical riding situations (such as low-speed drops). Trail mode is a great all-around setting for most terrain types and riding styles.

 

Descend Mode:

ctd-bv-d.jpg

Rotate the blue CTD lever fully counter-clockwise to set the shock to Descend mode. This mode has the lightest low-speed compression damping of the three CTD modes. Descend mode offers the most plush ride to ensure optimal traction over varied terrain.

Adjusting Trail Mode

Step 1

FLOAT CTD w/Adj models allow for added fine tuning

ctd-bv-t1.jpg ctd-bv-t2.jpg ctd-bv-t3.jpg

FLOAT CTD w/Adj model shocks feature a three-position Trail Adjust control that regulates low-speed compression damping only in Trail mode. 1 is the softest setting, 2 is the medium setting, and 3 is the firmest setting. To adjust Trail mode, first gently pull out on the black Trail adjust knob and turn it, lining up the arrow with your desired Trail mode setting number.

Trail adjustments (1, 2, 3) only function in Trail mode.

Using the CTD Remote

Step 1

Easy on-the-fly adjustments for unprecedented control and performance

ctd-dual-lever-new.jpg ctd-remote-all-modes.jpg

The CTD Remote lets you to switch between the Climb, Trail, and Descend modes while riding. Each mode is optimized for a specific type of terrain, providing best performance and riding enjoyment. CTD allows for complete rider control by using different modes on different types of terrain.

 

Climb Mode:

  • Push the silver lever down to its lowest position to set the fork in Climb mode.

Climb mode is a very firm low-speed compression setting (not designed to be a solid lockout). This setting is most useful for climbing and sprinting. 

 

Trail Mode:

  • From Climb mode, push the black release lever once and then push the silver lever down one click to the middle position to engage Trail mode.
  • From Descend mode, push the silver lever down one click to the middle position to engage Trail mode.

Trail mode offers less compression damping than Climb mode. Use this setting when pedaling on undulating terrain, and for preventing excessive travel in technical riding situations (such as low-speed drops). Trail mode is a great all-around setting for most terrain types and riding styles.

 

Descend Mode:

  • Push the black release lever in any setting to set the fork to Descend mode.

Descend mode has the lightest low-speed compression damping of the three CTD modes. Descend mode offers the most plush ride to ensure optimal traction over varied terrain.

Service Intervals

Step 1

Make sure to properly maintain your shock

service intervals rear shock.jpg

Air Sleeve Maintenance

Step 1

The air seals inside FOX air shocks do a lot of work and should be replaced regularly in order to maintain optimal performance and prevent wear. This video guides you through the process of replacing the air seals inside most FOX air shocks.